Dati tecnici
Dati tecnici - Valori elettrici
Tensione operativa
  • 8...30 VDC
Reverse polarity protection
  • Yes
Corrente operativa senza carico
  • ≤100 mA (24 VDC)
Initializing time typ.
  • 180 ms after power on
Interface
  • Profibus-DPV0
Function
  • Multiturn
Device adress
  • Rotary switches in bus cover
Steps per revolution
  • ≤2097152 / 21 bit
Number of revolutions
  • ≤65536 / 16 bit
Absolute accuracy
  • ±0,01 °
Principio di scansione
  • Ottico
Code
  • Binary
Immunità alle interferenze
  • EN 61000-6-2
Emissione di interferenze
  • EN 61000-6-3
Programmable parameters
  • Steps per revolution
  • Number of revolutions
  • Preset
  • Scaling
  • Rotating direction
  • Gear factor
Diagnostic function
  • Position or parameter error
  • Multiturn sensing
  • Operating hour counter
Status indicator
  • DUO-LED integrated in bus cover
Approvazione
  • UL approval / E217823
Dati tecnici - progettazione meccanica
Grandezza (flangia)
  • ø58 mm
Tipo di albero
  • ø6 x 10 mm, solid shaft with flat
Flangia
  • Synchro flange
Classe di protezione EN 60529
  • IP 54 (without shaft seal)
  • IP 65 / IP 67 (with shaft seal)
Velocità operativa
  • ≤6000 rpm (+25 °C)
Starting acceleration
  • ≤1000 U/s²
Coppia di spunto
  • ≤0,02 Nm (+25 °C, IP 54)
  • ≤0,04 Nm (+25 °C, IP 65 / IP 67)
Carico dell‘albero massimo ammesso
  • ≤40 N assiale
  • ≤80 N radiale
Materiale
  • Housing: aluminium
  • Flange: aluminium
  • Bus cover: zinc die-cast
  • Albero: acciaio inox
Temperatura operativa
  • -40...+85 °C (see general informations)
Relative humidity
  • 95 % non-condensing
Resistenza
  • EN 60068-2-6
  • Vibrazione ±0,75 mm - 10-58 Hz, 10 g - 58-2000 Hz
  • EN 60068-2-27
  • Urti 200 g, 3 ms
Peso ca.
  • 550 g
Allacciamento
  • Cable gland
  • Connector 3xM12

software
Software

Scaricare
Data sheet
Quickstart
Software Manual
Certificates / approvals

Accessori
Accessori di montaggio
The selected altAttribute does not exist! Set of eccentric fixings type A

Articolo n..: 11065545

  • With 3 eccentric fixings type A
The selected altAttribute does not exist! Mounting adaptor
For encoders with synchro flange

Articolo n..: 10117667

  • Glass-fiber reinforced plastic
  • Excellent resistance against temperature and chemicals
  • Electrically isolated encoder mount
The selected altAttribute does not exist! Set of eccentric fixings for mounting clamp (10117667)

Articolo n..: 10117668

  • With 3x eccentric fixings, screws and nuts
The selected altAttribute does not exist! Bearing flange for encoders with synchro flange (Z 119.035)

Articolo n..: 10158124

  • For all encoder with synchro flange and 6 mm shaft
  • Material: Aluminium, bare
The selected altAttribute does not exist! Spring washer coupling (D1=6 / D2=10)
For encoder with solid shaft

Articolo n..: 10141132

  • Backlash-free and angle-synchronous transmission of rotary movements
  • Plug-in version
  • Electric isolated
  • Suitable for very high speeds
  • Good compensation of all misalignments

In alto