2. GXN1H
Dati tecnici
Dati tecnici - Valori elettrici
Tensione operativa
  • 10...30 VDC
Reverse polarity protection
  • Yes
Corrente operativa senza carico
  • ≤50 mA (24 VDC)
Initializing time typ.
  • 50 ms after power on
Interface
  • Parallel (cams)
  • 5 special outputs programmable
Function
  • Multiturn
Number of cams
  • 250
Steps per revolution
  • ≤4096 / 12 bit
Number of revolutions
  • ≤4096 / 12 bit
Absolute accuracy
  • ±0,03 °
Principio di scansione
  • Ottico
Code
  • Binary
Code sequence
  • CW/CCW coded by connection
Inputs
  • TxD, RxD (RS232)
  • Control signals UP/DOWN inv. and zero
  • ENABLE inv.
Livelli di uscita
  • PNP or NPN open collector
Immunità alle interferenze
  • EN 61000-6-2
Emissione di interferenze
  • EN 61000-6-4
Programming interface
  • RS232
Programmable parameters
  • Steps per revolution
  • Number of revolutions
  • 2 presets (limits)
  • Rotation speed monitoring
Diagnostic function
  • Code continuity check
  • Signal frequency exceeded
Approvazione
  • UL approval / E63076
Dati tecnici - progettazione meccanica
Grandezza (flangia)
  • ø75 mm
Tipo di albero
  • ø14 mm (through hollow shaft)
Classe di protezione EN 60529
  • IP 54
Velocità operativa
  • ≤6000 giri/min (meccanico)
  • ≤6000 rpm (electric)
Coppia di spunto
  • ≤0,05 Nm (+25 °C, IP 54)
Rotore momento d‘inerzia
  • 20 gcm²
Materiale
  • Housing: steel
  • Flange: aluminium
Temperatura operativa
  • -25...+70 °C
Relative humidity
  • 95 % non-condensing
Resistenza
  • EN 60068-2-6
  • Vibrazione 10 g, 16-2000 Hz
  • EN 60068-2-27
  • Urti 200 g, 6 ms
Peso ca.
  • 700 g
Allacciamento
  • Cable 1 m, connector D‑SUB, 37‑pin
Scaricare
Data sheet
Quickstart
Software Manual
Certificates / approvals

Disegni
Drawings
The selected altAttribute does not exist!

(png | 141 KB)
Accessori
Accessori di montaggio
Mounting hollow shaft encoders – Rubber buffer element 18.5 mm long, as torque support (Z 119.037) Rubber buffer element 18.5 mm long, as torque support (Z 119.037)

Articolo n..: 11034095
  • Rubber buffer element as torque support
Mounting hollow shaft encoders – Shoulder screw M5 as torque support (Z 119.040) Shoulder screw M5 as torque support (Z 119.040)

Articolo n..: 11034097
  • Easy mounting in confined a place since no radial space required
  • For applications with limited space consumption
Mounting hollow shaft encoders – Torque support by rubber buffer for encoders with 15 mm pin (Z 119.041) Torque support by rubber buffer for encoders with 15 mm pin (Z 119.041)

Articolo n..: 10139345
  • Easy and cost-effective mounting
  • For applications with high acceleration
Mounting hollow shaft encoders – Spring coupling for GX and G1 (Z 119.043) Spring coupling for GX and G1 (Z 119.043)

Articolo n..: 10143969
  • Rigid spring coupling for high-dynamic applications
Connettori e cavi
Cables / connectors – Female connector D-SUB, 37-pin (Z 140.001) Female connector D-SUB, 37-pin (Z 140.001)

Articolo n..: 10160874
  • Female connector D-SUB, 37-pin
In alto