2. GXP1W - parallel
Dati tecnici
Dati tecnici - Valori elettrici
Tensione operativa
  • 10...30 VDC
Reverse polarity protection
  • Yes
Corrente operativa senza carico
  • ≤50 mA (24 VDC)
Initializing time typ.
  • 50 ms after power on
Interface
  • 24 parallel outputs
Function
  • Multiturn
Steps per revolution
  • ≤4096 / 12 bit
Number of revolutions
  • ≤4096 / 12 bit
Absolute accuracy
  • ±0,03 °
Principio di scansione
  • Ottico
Code
  • Programmable
Code sequence
  • CW/CCW coded and programmable by connection
Inputs
  • TxD, RxD (RS232)
  • Control signals UP/DOWN inv. and zero
  • ENABLE inv.
  • STORE inv.
Livelli di uscita
  • PNP or NPN open collector
Immunità alle interferenze
  • EN 61000-6-2
Emissione di interferenze
  • EN 61000-6-4
Programming interface
  • RS232
Programmable parameters
  • Steps per revolution
  • Number of revolutions
  • Code
  • 2 presets (limits)
  • Rotation speed monitoring
Diagnostic function
  • Self-diagnosis
  • Code continuity check
  • Multiturn sensing
Approvazione
  • UL approval / E63076
Dati tecnici - progettazione meccanica
Grandezza (flangia)
  • ø58 mm
Tipo di albero
  • ø10 mm solid shaft (clamping flange)
  • ø6 mm solid shaft (synchro flange)
Flangia
  • Clamping or synchro flange
Classe di protezione EN 60529
  • IP 54 (without shaft seal)
  • IP 65 (with shaft seal)
Velocità operativa
  • ≤10000 giri/min (meccanico)
  • ≤6000 rpm (electric)
Coppia di spunto
  • ≤0,015 Nm (+25 °C, IP 54)
  • ≤0,03 Nm (+25 °C, IP 65)
Rotore momento d‘inerzia
  • 20 gcm²
Carico dell‘albero massimo ammesso
  • ≤20 N assiale
  • ≤40 N radiale
Materiale
  • Housing: steel
  • Flange: aluminium
Temperatura operativa
  • -25...+70 °C
Relative humidity
  • 95 % non-condensing
Resistenza
  • EN 60068-2-6
  • Vibrazione 10 g, 16-2000 Hz
  • EN 60068-2-27
  • Urti 200 g, 6 ms
Peso ca.
  • 600 g
Allacciamento
  • Cable 1 m, connector D‑SUB, 37‑pin
Scaricare
Data sheet
Quickstart
Software Manual
Certificates / approvals
Declaration of conformity
CAD

Disegni
Drawings
The selected altAttribute does not exist!

(png | 115 KB)
The selected altAttribute does not exist!

(png | 116 KB)
Accessori
Accessori di montaggio
The selected altAttribute does not exist! Set of eccentric fixings type A

Articolo n..: 11065545
  • With 3 eccentric fixings type A
The selected altAttribute does not exist! Adaptor plate for clamping flange to convert into synchro flange

Articolo n..: 10141255
  • Adaptor plate for encoder with clamping flange for modification into synchro flange
The selected altAttribute does not exist! Mounting adaptor
For encoders with clamping flange

Articolo n..: 10125051
  • Glass-fiber reinforced plastic
  • Excellent resistance against temperature and chemicals
  • Electrically isolated encoder mount
The selected altAttribute does not exist! Bearing flange for encoders with synchro flange (Z 119.035)

Articolo n..: 10158124
  • For all encoder with synchro flange and 6 mm shaft
  • Material: Aluminium, bare
The selected altAttribute does not exist! Mounting adaptor
For encoders with synchro flange

Articolo n..: 10117667
  • Glass-fiber reinforced plastic
  • Excellent resistance against temperature and chemicals
  • Electrically isolated encoder mount
The selected altAttribute does not exist! Set of eccentric fixings for mounting clamp (10117667)

Articolo n..: 10117668
  • With 3x eccentric fixings, screws and nuts
The selected altAttribute does not exist! Spring washer coupling (D1=6 / D2=10)
For encoder with solid shaft

Articolo n..: 10141132
  • Backlash-free and angle-synchronous transmission of rotary movements
  • Plug-in version
  • Electric isolated
  • Suitable for very high speeds
  • Good compensation of all misalignments
Connettori e cavi
Cables / connectors – Female connector D-SUB, 37-pin (Z 140.001) Female connector D-SUB, 37-pin (Z 140.001)

Articolo n..: 10160874
  • Female connector D-SUB, 37-pin
In alto