2. Product Overview
  3. Product comparison

Solid shaft ø11 mm with EURO flange

  • Encoder with solid shaft ø11 mm
  • Max. 6000 pulses per revolution
  • Optical sensing method
  • Centering alignment ø85 mm, mounting screw hole circle ø100 mm
  • Industrial standard with centering flange
  • Dual bearing
  • TTL or HTL output signals
  • Flange connector radial or axial

Solid shaft with EURO flange B10

  • Size ø58 mm
  • Precise optical sensing (interpolated)
  • Output signal level programmable (TTL or HTL)
  • EURO flange B10
  • Connection axial, radial or tangential
  • Pulses per revolution 1...65536, programmable
  • High protection up to IP 67
  • High resistance to shock and vibrations
Technical data - electrical ratings
Approval UL 508 / CSA 22.2
Consumption w/o load ≤100 mA ≤70 mA
Duty cycle 45…55 % typical at 1024, 2048 ppr (further see table Duty cycle)
Emitted interference EN 61000-6-3 EN 61000-6-3
Initializing time ≤ 30 ms after power on
Interference immunity EN 61000-6-2 EN 61000-6-2
Output frequency ≤300 kHz (TTL)
≤160 kHz (HTL)		 ≤300 kHz (TTL)
≤160 kHz (HTL)
Output signals A, B, N + inverted A+, B+, R+, A-, B-, R-
Output stages TTL linedriver (short-circuit proof)
HTL push-pull (short-circuit proof)		 TTL/RS422
HTL/push-pull
Programmable parameters Output level TTL/HTL
Pulse number 1...65536
Zero pulse width 90°/180°
Zero pulse position
Signal sequence
Pulses per revolution 1000 … 6000 1 … 65536
Reference signal Zero pulse, width 90° Zero pulse 90° or 180°
Reverse polarity protection Yes Yes
Sensing method Optical Optical
Short-circuit proof Yes
Voltage supply 5 VDC ±5 %
8...30 VDC		 4.75...30 VDC
Technical data - mechanical design
Admitted shaft load ≤60 N axial
≤100 N radial		 ≤40 N axial
≤80 N radial
Connection Connector M23 type 2, 12-pin Flange connector M12, 8-pin
Flange connector M23, 12-pin
Cable
Flange EURO flange B10
Material Housing: aluminium
Shaft: stainless steel		 Housing: aluminium die-cast
Flange: aluminium
Solid shaft: stainless steel
Operating speed ≤8000 rpm ≤6000 rpm (+20 °C, IP 67)
≤12000 rpm (+20 °C, IP 65)
Operating temperature -20...+70 °C
-20...+100 °C		 -40...+100 °C
Protection EN 60529 IP 65 IP 65 (without shaft seal)
IP 67 (with shaft seal)
Relative humidity 90 % non-condensing 90 % non-condensing
Resistance EN 60068-2-6
Vibration 10 g, 55-2000 Hz
EN 60068-2-27
Shock 30 g, 11 ms		 EN 60068-2-6
Vibration 30 g, 10-2000 Hz
EN 60068-2-27
Shock 300 g, 6 ms
Shaft type ø11 mm solid shaft ø11 x 30  mm solid shaft with woodruff key
Size (flange) ø115 mm ø115 mm
Starting torque ≤0.015 Nm (+20 °C) ≤0.015 Nm (+20 °C, IP 65)
≤0.02 Nm (+20 °C, IP 67)
Weight approx. 950 g 485 g
To the top