2. Panoramica dei prodotti
  3. Misurazione delle distanze
  4. Sensori induttivi di distanza
  5. Robustezza
  6. IR18V.D08L-F50.UA1Z.9BDU/0035_A002_E010
Dati tecnici
Dati generali
Mounting type
  • Flush
Special type
  • Linearized
  • Vehicle
Measuring distance Sd
  • 0 … 8 mm
Sensitivity
  • 0,5 V/mm
Resolution
  • < 0,008 mm (stat.)
  • < 0,01 mm (dynam.)
Repeat accuracy
  • 0,016 mm
Linearity error
  • ± 120 µm
Temperature drift
  • ± 8 % (Full Scale)
Approvals/certificates
  • EN 60947-5-2 / EN 60947-5-7
  • EN 13309:2010
  • EN ISO 14982:2009
  • ISO 13766:2006
Dati elettrici
Response time (factory characteristic)
  • < 1 ms
Tensione di alimentazione +Vs
  • 4,75 … 5,25 VDC
Corrente assorbita max. (senza carico)
  • 12 mA
Circuito di uscita
  • Voltage output
Output signal
  • 0,5 ... 4,5 VDC
Load resistance
  • > 4500 Ohm
Protezione da cortocircuito
  • Si
Off-Highway Electromagnetic immunity
  • ISO 11452-4: 200mA
  • ISO 11452-2: 100V/m
  • Based on UN / ECE R10 Rev 5 ch. 6.8 (no ECE type approval available)
Off-Highway Emission
  • EN 55011
  • Based on UN / ECE R10 Rev 5 ch. 6.5, 6.6 (no ECE type approval available)
Dati meccanici
Design
  • Cylindrical threaded
Material (sensing face)
  • PBT
Housing material
  • Brass nickel plated
Dimension
  • 18 mm
Housing length
  • 50 mm
Connection types
  • Flylead connector DT04-3P 3 pin
Tightening torque max.
  • 40 Nm (A: 28 Nm, B: 28 Nm)
Condizioni ambientali
Temperatura d'esercizio
  • -40 … +85 °C
Tipo di protezione
  • IP 68 (sensing face/sensor)
  • IP 68 (1,5 m, 24 h)
  • IP 69K (sensing face)
Modello 3D
Modello 3D

La creazione di modelli CAD richiede una registrazione esterna presso CADENAS.

Scaricare
Data sheet
Quickstart
Certificates / approvals
EPLAN

Disegni
Drawings

(png | 117 KB)
Connection diagram

(png | 67 KB)
Pin assignment

(png | 60 KB)
Accessori
Mounting accessories
Sensofix series 18

Articolo n..: 10151658
  • Clamps made of stainless steel
  • Ball pivots made of galvanized steel
  • Mounting panel made of stainless steel
ZADAP-M18.STANDARD
Mounting bracket series 18

Articolo n..: 11172096
  • Material: Steel galvanized
ZADAP-M18.SHORT
Mounting bracket short series 18 (L design)

Articolo n..: 11171584
  • Material: Steel galvanized
ZADAP-M18.LONG
Mounting bracket long series 18 (L design)

Articolo n..: 11172095
  • Material: Steel galvanized
The selected altAttribute does not exist! Mounting rod with mounting plate holder 200 mm

Articolo n..: 11707685
  • Material: Aluminium
  • Part of an assembly
  • Different lengths available
The selected altAttribute does not exist! Mounting rod with mounting plate holder 300 mm

Articolo n..: 11707686
  • Material: Aluminium
  • Part of an assembly
  • Different lengths available
The selected altAttribute does not exist! Mounting rod 200 mm

Articolo n..: 11707688
  • Material: Aluminium
  • Part of an assembly
  • Different lengths available
The selected altAttribute does not exist! Mounting rod 250 mm

Articolo n..: 11707697
  • Material: Aluminium
  • Part of an assembly
  • Different lengths available
The selected altAttribute does not exist! Mounting rod with mounting plate holder 250 mm

Articolo n..: 11707698
  • Material: Aluminium
  • Part of an assembly
  • Different lengths available
The selected altAttribute does not exist! Mounting rod 300 mm

Articolo n..: 11707687
  • Material: Aluminium
  • Part of an assembly
  • Different lengths available
The selected altAttribute does not exist! Mounting plate series 500 and ø18 mm

Articolo n..: 11707699
  • Material: Steel
  • Part of an assembly
The selected altAttribute does not exist! Mounting base

Articolo n..: 11707702
  • Material: Plastic (PA)
  • Part of an assembly
The selected altAttribute does not exist! Two-way connector

Articolo n..: 11707703
  • Material: Plastic (PA)
  • Part of an assembly
In alto