2. EIL580-SQ/EIL580P-SQ
  3. Product comparison

Solid shaft and flange in inch dimensions

  • Robust design with protection up to IP 67
  • Solid shaft loading up to 150 lbs (670 N)
  • Shock resistant up to 100 g's
  • Operating temperature -30...+100 °C
  • Max. 6000 pulses per revolution without interpolation

Solid shaft with square flange

  • Size ø58 mm
  • Precise optical sensing
  • Output signal level TTL or HTL
  • Square flange 2.5" (63.5 mm)
  • Connection axial, radial or tangential
  • Pulses per revolution up to 5000
  • High protection up to IP 67
  • High resistance to shock and vibrations
Technical data - electrical ratings
Approval UL 508 / CSA 22.2
Consumption w/o load ≤30 mA (24 VDC)
≤60 mA (5 VDC)		 ≤70 mA
Duty cycle 40…60 %
Emitted interference EN 61000-6-4 EN 61000-6-3
Interference immunity EN 61000-6-2 EN 61000-6-2
Output frequency ≤150 kHz ≤300 kHz (TTL)
≤160 kHz (HTL)
Output signals A, B, Z
A, B, Z + inverted		 A+, B+, R+, A-, B-, R-
Output stages Linedriver/RS422
Push-pull short-circuit proof		 TTL/RS422
HTL/push-pull
Phase shift 90 ° ±10°
Pulses per revolution 5 … 6000 100 … 5000
Reference signal Zero pulse, width 90° ±10 %
Reverse polarity protection Yes (4.75...30 VDC) Yes
Sensing method Optical Optical
Short-circuit proof Yes (HTL)
Yes (TTL, max. 1 s and 1 signal)
Voltage supply 5 VDC ±10 %
4.75...30 VDC		 5 VDC ±5 %
8...30 VDC
4.75...30 VDC
Technical data - mechanical design
Admitted shaft load ≤80 lbs (350 N) axial/radial
≤100 lbs (450 N) axial or
≤150 lbs (670 N) radial		 ≤40 N axial
≤80 N radial
Bearing life 1.6 x 1010 rev. at 10 % of rated shaft loading (8 lbs axial/radial)
Connection MIL-connector, 7-pin
MIL-connector, 10-pin
Cable 1 m		 Flange connector M12, 8-pin
Flange connector M23, 12-pin
Cable
Flange Clamping flange square 2.5" x 2.5" (63.5 x 63.5 mm) Square flange 2.5" (63.5 mm)
Material Housing: aluminium
Flange: aluminium		 Housing: aluminium die-cast
Flange: aluminium
Solid shaft: stainless steel
Operating speed ≤10000 rpm (IP 54)
≤6000 rpm (IP 67)		 ≤6000 rpm (+20 °C, IP 67)
≤12000 rpm (+20 °C, IP 65)
Operating temperature -30...+100 °C (5 VDC)
-30...+85 °C (24 VDC)		 -40...+85 °C
Protection EN 60529 IP 54 (without shaft seal)
IP 67 (with shaft seal)		 IP 65 (without shaft seal)
IP 67 (with shaft seal)
Relative humidity 95 % non-condensing 90 % non-condensing
Resistance EN 60068-2-6
Vibration 10 g, 10-2000 Hz
EN 60068-2-27
Shock 100 g, 6 ms		 EN 60068-2-6
Vibration 30 g, 10-2000 Hz
EN 60068-2-27
Shock 300 g, 6 ms
Rotor moment of inertia 14.5 gcm²
Shaft type ø0.375" (ø9.52 mm) solid shaft ø10 x 20 mm, solid shaft with flat
ø3/8" x 4/5" (ø9.525 x 20.32 mm), solid shaft with flat
Size (flange) 2.5 x 2.5" (63.5 x 63.5 mm) 2.5 x 2.5" (63.5 x 63.5 mm)
Starting torque ≤0.015 Nm (+25 °C, IP 54)
≤0.03 Nm (+25 °C, IP 67)		 ≤0.015 Nm (+20 °C, IP 65)
≤0.02 Nm (+20 °C, IP 67)
Weight approx. 12.5 oz.
350 g		 370 g
To the top